SRM6210E Ethernet Radio Modem for the
902 to 928 MHz ISM Band

SRM6210E Wireless Ethernet radio modem for data transfer in the 902-928 MHz ISM band shown with mounting flanges in two of four positions. Optional DIN rail clip available.

Class 1 Div 2 certification License-free wireless—operates in the 902-928 MHz ISM (industrial/scientific/medical) band Compact, flexible design with universal mounting—back panel or on optional DIN rail clip Rated range of up to 25 miles (40 km) and an installed range of up to 35 miles (56 km) in optimal conditions with line-of-sight and an omni directional antenna— farther with Repeaters or higher gain antennas Employs Smart Spectrum™ frequency hopping technology for exceptional data integirty—even in high noise environments Wirelessly connects Ethernet PLCs and workstations Factory configured for your application—ensuring trouble-free installation User configurable for Master, Remote, Repeater or Repeater/Remote mode Front panel LEDs. Power, RF Link, RF In, RF Out, LAN In, LAN Out, LAN Link, LAN Collision, Overrun Error PLC slot mount versions also available

The SRM6210E employs Smart Spectrum™ frequency hopping spread spectrum (FHSS) technology in the 902-928 MHz frequency band for secure, robust communication. Data-Linc Group’s FHSS technology, coupled with 32-bit CRC error detection, enables the SRM6210E to reliably deliver critical information.

RF site surveys are usually unnecessary and an FCC site license is not required. The SRM6210E wireless technology eliminates the need for hard wire or fiber cable, which are often expensive and difficult to install.

The SRM6210E offers easy to read LEDs and affords maximum installation flexibility, including optional DIN rail mounting. The SRM6210E can bridge two Ethernet segments or connect multiple Ethernet nodes to a Master PLC. The SRM6210E offers a 10BaseT (UTP) interface to the Ethernet device, uses MAC layer filtering and fully supports most Ethernet protocols for true protocol transparency.

The SRM6210E supports a number of configurations, including point-to-point and point-to-multipoint as well as multiple Repeaters if required. Multipoint operation permits an unlimited number of Remotes. The SRM6210E can also function as a Repeater/Remote to extend range or work around obstructions. Back-to-back radio modems are not required for Repeater function but can be used to maximize data throughput.

As with all Data-Linc products, support services such as pre-sale project consultation, post-sale tech support with PLC expertise and site survey planning assistance are part of the Data-Linc Group commitment.

For high speed, long-range frequency hopping needs, please see the SRM7210E data sheet.

Download a printable pdf (516K) version of this SRM6210E data sheet.
To read pdf files you need to get Adobe Acrobat Reader and install it on your PC.

Certification
Class 1 Div 2

Antenna
Standard thread SMA female.
Supplied bench test antenna
Optional external omni directional or yagi antenna

Power
Input Voltage Requirements. 10 to 28 VDC;
115 VAC to 12 VDC wall mounted transformer provided
Connector. Latching screw terminal
RF Output Power. 0.1 to 1.0 watt
Transmit Current (Peak). 700mA @ 12 VDC for 1 Watt
Receive Current. 100ma @12 VDC

Operating Modes
Point-to-point, point-to-multipoint, Store-and-Forward Repeater, Repeater/Remote
Configuration. Serial port 19.2 Kbaud terminal based

Diagnostics
Front Panel LEDs. Power, RF Link, RF In, RF Out,
LAN In, LAN Out, LAN Link, LAN Collision, Overrun Error
Serial Port Data. Stored signal strength, noise and disconnect information
Optional. LincView^TM OPC Diagnostic Software for real-time RF network monitoring.

Operating Environment
Standard Temperature. -40° to 167°F (-40° to 75°C)
Humidity. 0 to 95% non-condensing humidity

Weight
1.94 lb (.88 kg)

Enclosure
Standard. NEMA 1; 18-gauge steel; 2.45x3.42x6.3”
(6.22x8.69x16 cm)
Mounting. Two “L” brackets on either side, rear, top or bottom for panel mounting. Optional DIN rail clip

Enclosure